Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
What're your opinions concerning Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately tough project. If the old tub is conveniently available, the job can relocate rapidly; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new bath tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will require a helper to move out the old tub and also embeded in the brand-new one. Make certain you have qualified on your own for the job and also fit attempting it. As opposed to working with a specialist to take over a halfway-completed job, it is far better to consider using one before you begin. Opportunities are you might need an expert plumber to make tube connections.
This write-up will aid you mount a new tub in your bathroom if you have already purchased a brand-new tub and also do not require to transform the arrangement of your previous water supply pipelines.
Your tools and product checklist need to make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be quite problematic because of the restricted access that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to going on to fit the new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place in between the faucet as well as the sink. Protect the tap in position with the producer provided backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The former type needs to be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bathtub
Using both wooden boards under its feet, position the bath tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out level.
To install taps, fit the bottom of the outermost flexible faucet adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Fill up the tub and likewise examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub ought to wait until the tub has been utilized at least when as this will resolve it right into its last setting.
Getting ready for the Installment
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to stop strain on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, causing the water to pass through the wall in between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, and are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub remains in usage. The sealant can split fairly very early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that piece of writing about How to Install a Bathtub Yourself while doing a lookup on the search engines. Are you aware of anybody else who is involved in the topic? Take a moment to promote it. Thanks a lot for your time. Visit us again soon.
Plumbing insights available. Report this page